Image : http://www.flickr.com
When ready, the layout design of the alarm system for installation, you first need to decide where to mount the alarm control. If you have an unfinished basement, will be to drill and run the cable into the beam area and the panel. Very often this is the mechanical or boiler is.
If you are on a house one floor, will run the cable to the attic and an unfinished
Put your wires toControl.
If you are in a commercial application that you run the wires along the ceiling or beams or may be suspended from Conduit.
If you're in a place where there is no place to run all those wires and hide them, then you are a candidate for a wireless system.
We want to make sure that wherever you decide to mount the base unit that you have a device, such as to protect a motion detector or door contact. Leaving the control panelin an unprotected area may make it easy to circumvent in the event of a break in the wires Look through the underground, and when they jump up to a closet in the protected area of the house. If you're wondering, "what is the bare wires in the basement?". Cut the wire duplication with the opening of the device they run, and would trigger an alarm when the system was armed.
If you choose to go wireless click on your system,Choose a central location in your home or office, the protection of the radio signal received by all the strengths. Remember that even the wireless system, there are some cables should be run. For the most part are the keypad, siren, power supply and telephone line. Take this is taken into account when choosing your location.
Type of lighting for the selected area, as this will be where you do most of your installation to work. Set aPlane and space for all products and tools and a trash bag in this area. I have learned over the years, come to my home, to get what I need, and return that I do not use, are back in this place when I'm done with them, especially tools. If you are not an organized system, you will spend your research time and a half for a tool that is part of the wire coil, etc. A practical tool belt for all the tools you need anywhere, as fresh drill, tape, pliers ,Screwdriver, B-connection, a small bubble level, stud finder, a cloth, etc.
There is also the way you go. At the end of each wire and run the installation of the device will take the time to clean up and bring all the waste in the bag for the control area. Being anal is a good thing if you run a quality installation.
As each wire in the control room, where the measure has come into the thread hole control panel, and then run about a foot of wire Addbefore cutting with a knife. Place a piece of luminous tape on the wire about 5 cm from and write to the tape with a Sharpie permanent marker, or where it goes.
If your home or office is under construction, you can choose to take the security pre-wire it. Pre-wiring is the ability to obtain all the devices the exact situation, it would be an advantage. Wires and the positioning of the gear boxes is completed before construction isdepending on the ability to read architectural plans and see where furniture, appliances and electrical devices to be placed precisely. If you pre-wire you must give your own holes in the wall studs and rafters. Many technicians will think bad of an alarm through the holes in the electrical and plumbing and are easy to do to get away. The problem is that if you're an electrician or plumber no inspection to be carried by cable and pipe in order to shiftSpecific settings. Are not suitable to discuss your wire when to be affected.
The best time to get your wires on a pre-wire after an electrician and left to go before the insulation.
If you start the clutter of wires, we start with the front door. If you're in the basement where you will turn on the low door opening. If you use the cable to work until you reach the top of the door. Lets use that to ourExample. What kind of contact will be with you? Surface mount or flush? If you wire anyway, why not take the time to install recessed contacts so that they are from the site when the door is closed? Set the drill bits with a 3/8-inch standard length.
In the jam of the door, about 4 cm from the bottom to begin the drilling of an angle to the basement. Go to your 12-18 cm 3/8- inch drill bit and towards the base,Finally, to switch your long 5-foot hook bit 'bell drill and continue to pop into the cellar. Pull out the long tip of the hole and remove it from the hole. Poke the thin end of the long bit in the hole.
Go to the basement with a flashlight, diagonal cutters, duct tape, marker, stapler with staples, and a second reel or box of 22 gauge wire. Strip the plastic off the end of your wire about 2 cm. Switch the two wires together and thread themthrough the hole at the end of the lean part of the bit 'long run. Go back upstairs and pull the wire to the hole. Tie a large knot loose and temporary wire after it arrive, so do not fall into the hole. Allow at least 12 inches upward, allowing you work with the wire.
Go down and begins to roll enough wire to your Control Panel. Staple the wires with an industrial stapler as a T22 along the bar in aso clean and tidy from the hole down in the direction of the Panel. Be sure not to permeate the wire with every basic food, if you now remove and reattach. These errors are hard to follow after you walk. Be sure to put down the stud wall where you put high on the back of the control panel (like the breast) and leave a foot or more before cutting the wire from the coil. Check the cable for the tape and markers from several inchesEnd.
Congratulations, you have your first run. Be sure to collect and return all tools to the starting point, so you know where they are when you need them.
Get your 8.3-inch frame and magnet. You need a drill, extension cord (unless you use a cordless drill), duct tape, wire and a cutter. Split ends wire and strip a small amount of plastic covering away from each end. Do the same with your data if you have the type that is small,Screws for the wires to be blocked. Twist each end of the wire at one end of the contact wire and tape down individually. After all a piece of tape firmly around the whole handle. (It does not matter which wire on the scale, because it is a wire loop, and has no positive or negative.) Carefully insert the wire into the hole and press contact now Mark inside the door of the place is that the magnet is the contact when the door is closed only.to stabilize the door and drill a 3 / 8 "hole just deep enough to contact the magnet on Repeat for each port you want. We always recommend contacting every perimeter door contact.
We are instructions for additional wiring for the device expert know-post! Alarms Web site for access.
Check back soon! because we are adding do-it-yourself installation techniques are often plants.
yai